Blisters on asphalt shingles form when trapped moisture vaporizes under heat, lifting the granule surface. The correct fix involves sealing the blister's edge with roofing cement or replacing damaged shingles entirely.
Shingle blisters typically appear as raised, bubble-like patches on the roof surface. They develop when moisture gets trapped between the shingle's fiberglass mat and its protective asphalt coating. Heat from the sun causes the moisture to turn to steam, pushing the top layer upward. This compromises the shingle's integrity and increases the risk of water intrusion.
According to the National Roofing Contractors Association (NRCA), blisters are most common in new roofs exposed to direct sunlight during installation, especially in hot climates. The problem often resolves itself within six months as the shingle cures, but persistent blisters require intervention.
Blisters occur when moisture becomes trapped during manufacturing or after installation. During hot weather, the trapped vapor expands, creating pressure that lifts the shingle's surface. Once the seal fails, wind or rain can enter through the weakened area.
Unaddressed blisters lead to premature shingle failure. A study by the Asphalt Roofing Manufacturers Association (ARMA) found that blisters reduce a shingle's lifespan by up to 30% when left untreated. They also create uneven surfaces that interfere with proper water runoff.
For example, a homeowner in Phoenix reported a blistered area measuring 6 inches by 4 inches after a summer heatwave. The blister cracked open during a storm, allowing water to seep into the attic. The resulting mold growth required $3,200 in remediation work.
Do not apply standard caulk or silicone. These materials degrade under UV exposure and fail within months. Instead, use roofing cement specifically designed for asphalt shingles.
Roofing cement should be applied in a continuous bead around the blister's perimeter. It must be thick enough to fill gaps and bond securely to both the shingle and the surrounding surface. Use a trowel or putty knife to press the cement into place.
For larger blisters (over 2 inches in diameter), cut out the affected section and replace the shingle. Use a utility knife to score the edges, then lift the shingle with a flat pry bar. Install a new shingle that matches the existing ones in color and thickness.
| Blister Size | Recommended Action | Materials Needed |
|---|---|---|
| Under 2 inches | Seal with roofing cement | Asphalt roofing cement, trowel, safety gloves |
| 2-4 inches | Seal and reinforce with mesh patch | Cement, fiberglass mesh patch, roller |
| Over 4 inches | Replace shingle | New shingle, pry bar, hammer, nails |
A common mistake is covering blisters with paint or sealant not rated for roofing. These products lack flexibility and crack under thermal expansion. The NRCA warns against using exterior-grade paints on shingles-they trap moisture and accelerate deterioration.
Using household adhesive, duct tape, or even roofing tar from a hardware store is ineffective. These materials do not adhere well to asphalt and break down under UV light.
Some homeowners attempt to "pop" blisters with a needle. This creates a hole that allows water entry. The NRCA explicitly advises against puncturing blisters-once the seal is broken, the shingle cannot reseal itself.
I once observed a contractor in Texas attempt to cover a 3-inch blister with a piece of scrap metal. After one monsoon season, the metal had rusted and lifted, causing a leak. The repair cost $1,800 to fix-three times the original repair budget.
If blisters appear in clusters or cover more than 10% of the roof, consult a licensed roofer. Multiple blisters may indicate poor ventilation or inadequate attic insulation, which contribute to moisture buildup.
For roofs older than 10 years, blisters are often signs of aging rather than new defects. In such cases, replacement may be more cost-effective than repair. ARMA states that shingles past their warranty period (typically 20-30 years) rarely benefit from localized fixes.
After inspecting a roof in Atlanta, a certified inspector noted that 72% of blisters occurred near vents and chimneys-areas with poor airflow. He recommended installing ridge vents and soffit baffles to improve attic circulation, reducing future blister formation.
Proper attic ventilation reduces temperature and humidity spikes that cause blisters. Ensure soffit and ridge vents are unobstructed. The EPA recommends maintaining a 1:150 ratio of vent area to attic space.
During installation, avoid laying shingles in direct sunlight. NRCA guidelines state that shingles should be installed between 7 AM and 3 PM in temperatures below 90°F to allow proper bonding. Installing in high heat forces rapid drying, increasing the chance of trapped moisture.
Regular roof inspections every 6 months catch blisters early. Use binoculars from the ground to spot irregularities. Replace any shingle showing granule loss or soft spots.
Understanding what to put on shingles blisters prevents costly repairs. Sealing small blisters with proper roofing cement stops leaks. Replacing large or multiple blisters ensures long-term protection. Always use materials approved for roofing, not generic adhesives.